DYEGOO GT02D отслеживание в реальном времени несколько сигналов тревоги высокая точность GPS трекер для

The tracker working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet.

Overview of the characteristics:

1.GPS position.

2.GSM 850/900/1800/1900MHZ.

3.Vibration sensor inside.

4.Wide voltage range:9-40V.

5.Oil-cut function.

6.ACC detection.

7.Overspeed alarm.

8.Vibration alarm.

9.Power-Cut alarm.

Specification:

1).GSM:850/900/1800/1900MHZ

2).GPRS: Class12, TCP/IP

3).Working Voltage:9-40V DC

4).Working current:≈22mA (12VDC)

5).Working current:≈12mA (24VDC)

6).GPS locating time:Cold start≈38s(Open sky)

       Warm start≈32s

       Hot start≈2s(Open sky)

7).GPS Precision:10m(2D RM)

8).Working temperature:-20℃~+70℃

9).Working humidity:20%~80%RH

10).Measurement:90(L) x 45(W) x 13.5(H) mm

Installation

1 Preparation before installation

1.1 Open the packing box to check whether the type of device is correct and whether the accessories are included.

1.2 This product is a high-tech electronic device, installation should be undertaken by a professional.

1.3 Please follow the following procedures to install your GT02D.During installation, there should be no power to the device.

1.4 Installing SIM card:

The device need to insert a SIM card which support GSM 2G network. The SIM card used should be enabled for GPRS.

1. Testing SIM card: to test SIM card, please install it into a normal GSM mobile and ensure it can send and receive SMS, and enables for GPRS.

2)    Installing SIM card: Remove the upper cover of device, insert SIM card as shown then replace cover, lock the shell with 4 bolts.

2 Installation

The GPS tracker must be installed under professional personnel.

Note:

1) Please install the device in the hidden place as followings:

Under Front windshield;

In the front instrument panel;

Under back windshield;

2) Avoid being placed with signal radiators like reverse sensor ;

3) The device has GSM antenna and GPS antenna inside. Please ensure the receiving side of the device is face up and without metal cover.

Note: The metal cover will lessen the receiving of GPS signals.

3 Selecting installation place and fixing it.

There are two kinds of installation: covert and non covert.

3.1 If you need the covert installation, please refer installation to an auto electrical contractor.

Note:

1. To prevent theft of the GT02D,the device should be installed as covertly as possible.


2. Avoid placing the GT02D close to higher power electrical devices, such as reversing radar, anti-theft device or other vehicle communication equipment.


3. The GT02D should be fixed into position with cable ties or wide double-side tape.


4. Your device has built-in GSM antenna and GPS antenna. During installation, please make sure the receiving side face is up, with no metal object above the device to interfere with GPS reception. The following places are suggested for installation

 Under the dash board below the front windshield;

- In the parcel shelf in the rear;

- In the front bumper( non-material face), please ensure the device cannot get wet;

- Under the wiper version (non-metal), please ensure the device cannot get wet;

Notice: If the windshield is pasted with metal thermal-protective coating, it may affect the performance of the device. In this case, please change the installation place after consulting the professional.

3.2 Non Covert Installation,

Firstly fix the device on the dash board below windshield.

- In the parcel shelf in the rear;

- In the front bumper( non-material face), please ensure the device cannot get wet;

- Under the wiper version (non-metal), please ensure the device cannot get wet;

Notice: If the windshield is pasted with metal thermal-protective coating, it may affect the performance of the device. In this case, please change the installation place after consulting the professional.

Manual Download By QR Code: